Comparison
REAP and your vendor’s AI assistant
Use both. The assistant your network vendor ships knows its own devices well: their configuration, their telemetry and the recommendations for that estate. REAP reasons across every vendor in the estate plus the tickets and configuration history between them. This page is for the colleague who asked which one you need.
The short answer
Each knows something the other cannot
A vendor’s assistant is built on that vendor’s devices. It reads their state, knows their commands and their failure modes, and recommends what that vendor would recommend. That is valuable, and nothing about REAP asks you to switch it off.
REAP is built on the estate. It reads from every vendor in scope, from the ITSM, from the configuration history and from the topology between them, runs one investigation across all of it, and writes the finding and its evidence back to the ticket your team already uses. The assistant’s answer becomes one more piece of evidence in that investigation, with its source named.
The test that tells you which you need on a given day is the boundary. An incident inside one vendor’s estate may be the assistant’s to solve. An incident that crosses vendors, or follows a change made in another tool, or has to be explained to an auditor six months later, is REAP’s.
What each is for
The same questions, two tools
Neither column is a criticism of the other. The rows are the questions a network team actually asks.
| Question | Your vendor’s assistant | REAP |
|---|---|---|
| Why is this device misbehaving? | Its home ground: configuration, telemetry and known issues for that platform, often with a recommended fix. | Reads the same state through the connector cluster, then asks what changed around the device: the ticket, the configuration diff, the path. |
| Why is this service down? | Answers for the devices it manages; the path through another vendor’s switch, the cloud account or the firewall is outside its view. | Traces the path forward, in reverse and at a past point in time across every vendor in it, and names the change or condition behind the failure. |
| What changed? | Changes made through its own controller or CLI. | Changes from any source: the ITSM record, the configuration history, an unrecorded change found by drift detection. |
| Did the change work? | Not its question: it reports the device’s state after the change. | Compares state before and after against the change’s intent and writes one verdict to the change record. |
| Will failover hold? | Reports the standby’s state on its own platform. | Checks standby sync, running-versus-startup drift and backup-path capacity across the pair, and in a pilot runs the failover test with your team. |
| Can we show the evidence? | The device output it used, inside its own console. | Every conclusion linked to its evidence in the Investigation Window and in the ticket, for anyone who was not in the room. |
Together
How they work on the same incident
Nothing is replaced and nothing is duplicated; the assistant stays the expert on its devices and REAP owns the investigation across them.
The incident opens in the ITSM
Your monitoring raises it, or REAP’s own rules do from the telemetry it collects. The ticket is the record both tools write to.
REAP runs the investigation
It forms hypotheses, gathers evidence from every vendor in the path and from the configuration history, and changes course when the evidence says so.
The assistant answers for its devices
Where the investigation reaches one vendor’s estate, the assistant’s state and recommendations are read as evidence, with the source named.
The finding goes back to the ticket
What changed, why it broke, what is affected and what to do next, with the evidence linked, in the ticket your team already uses.
Any action runs under approval
Read-only by default; a write runs only inside a procedure you approved, behind a confirmation, and is logged with the device output. The assistant’s own actions stay under its own controls.
Questions
The assistant and REAP: straight answers
We have one vendor. Does REAP add anything?
Two things the assistant does not do: it verifies a change against its intent and writes the verdict to the change record, and it proves failover before it is needed. If your last P1 followed a change that had closed as successful, start there; if not, your vendor’s tools are the right next step today, and the decision tree says when to come back.
Does REAP need the assistant switched off?
No. REAP reads device state through its own connector cluster with read-only credentials; the assistant keeps working as it does today. Where the assistant exposes an API, its answers can be read as evidence.
Which vendors does REAP support?
Cisco (opens in a new tab), Arista (opens in a new tab), Juniper (opens in a new tab), HPE Aruba (opens in a new tab) and Palo Alto Networks (opens in a new tab) are on the supported list; coverage for Fortinet (opens in a new tab), SONiC (opens in a new tab) and other platforms is confirmed per pilot against your platforms and versions. The integrations page keeps the list current.
Does REAP compete with my vendor?
REAP is not a network vendor and sells no hardware or controllers. It is the reasoning and assurance layer above the tools you already run, including the assistant; the vendor stays the expert on its own devices.
Bring us an incident that crossed a boundary.
Then see how REAP connects network evidence across every vendor in the path to help engineers investigate incidents faster: a 30-minute session, evidence first.